MiniRail System

The MiniRail mounting system for photovoltaic assemblies was developed specifically for trapezoidal sheet metal. It allows easy changing of the module orientation thanks to the universal module clamps which are rotatable by 90°, is extremely lightweight and comes stacked completely on pallets.

  • Innovative and statically optimised short rail system that is quick and easy to mount
  • Universal module clamps and suitable for portrait and landscape orientation
  • 5° elevation with MiniFive: significantly more output thanks to improved ventilation and optimised solar irradiation
  • Optimised for storage and transport

  • Symbol Flachdach
  • Symbol Trapezblech
  • Symbol Sandwich-Trapezblech
  • Symbol Palettenware

5° elevation with MiniFive

Significantly more yield through... 

 

  • Improved rear ventilation 
  • Optimized irradiation angles
  • Superior module performance 

 




Module orientation

The MiniRail system allows portrait and landscape mounting as grid mounting by means of the universal module clamp MiniClamp, which can be rotated by 90°.

The complete assembly system on one pallet

 

The compact dimensions of the MiniRail system allow very small packing dimensions and low weight. Therefore almost all means of transport are possible at low cost and you are not dependent on large, expensive means of transport. 
The system actually consists of only five components and is therefore very clear when unpacking. 

References

MiniRail components

Downloads

available in the respective languages 

Product data sheet and brochures

Assembly instructions and checklists

Certificates and tender specification

Document type
MCS Certificate  IK0182 04
Tender specification  MiniRail
Tender specification  MiniRail with MiniFive

Videos

Technical data

 
MiniRail System
Scope of application

Pitched roofs with trapezoidal sheet metal or sandwich panels Roof inclination: 5 - 75°

Fastening type / roof fixture

Screws in roofing with self-tapping thin sheet screws

Requirements

  • Sheet thickness: ≥ 0.4 mm steel and ≥ 0.5 mm aluminium
  • Sandwich panel: Approval from ­manufacturer required
  • Crest width: At least 22 mm *
  • Crest spacing: 101 - 350 mm depending on crest width
  • Flush area surrounding the bore hole: Ø ≥ 20 mm
  • Module frame height: 30 - 50 mm
Module orientation

Vertical or horizontal

Material

Aluminium (EN AW-6063 T66 / EN AW- 6082 T6); EPDM

Dimensions MiniRail W × H × L [mm]

78.2 × 23 × 385

Elevation with MiniFive

approx. 5°

MiniRail System
Scope of application

Pitched roofs with trapezoidal sheet metal or sandwich panels Roof inclination: 5 - 75°

Fastening type / roof fixture

Screws in roofing with self-tapping thin sheet screws

Requirements

  • Sheet thickness: ≥ 0.4 mm steel and ≥ 0.5 mm aluminium
  • Sandwich panel: Approval from ­manufacturer required
  • Crest width: At least 22 mm *
  • Crest spacing: 101 - 350 mm depending on crest width
  • Flush area surrounding the bore hole: Ø ≥ 20 mm
  • Module frame height: 30 - 50 mm
Module orientation

Vertical or horizontal

Material

Aluminium (EN AW-6063 T66 / EN AW- 6082 T6); EPDM

Dimensions MiniRail W × H × L [mm]

78.2 × 23 × 385

Elevation with MiniFive

approx. 5°

* The project-specific minimum high crest width dimension can be found in the Base On report. 

Dimensioning scheme MiniRail

Dimensioning scheme MiniRail

 

w = width / H = height / L = length