Bereich auswählen

    Dome 6 Systems

    • 80% pre-assembled and 70% faster to install thanks to improved components
    • The handy Dome Speed Spacer distance gauge provides time-saving rail alignment
    • Secure anchoring with fixed connection for roofs ≤ 5° and low load reserves
    Symbols Properties Dome 6 Mounting systems

    Components and their advantages

    70 % faster installation

    • Significantly shorter installation time of Dome 6 compared to the predecessor model Dome V
    • Thanks to improved, pre-assembled components, new hitch pin technology and the distance gauge
    Rail sets Dome 6 and Peak assembly

    Pre-assembled rail sets

    • Designed for current and future module sizes
    • Set completely pre-assembled and click system for Peaks
    • Tool-free assembly without screws

    RailConnector

    • Quick and easy rail connector with hitch pin
    • No screw connection necessary
    • Compensates tolerances by means of floating bearings
    Universal module clamps MiniClamp EC/MC

    Universal module clamps:

    MiniClamp MC/EC

     

    • Clamping range 30 - 50 mm
    • Compatible with MiniRail, MicroRail and Dome V systems
    • Optional: Potential equalization with TerraGrif possible
    Mat S

    Mat S

    • Shear soft Mat S made of EPDM – only 1 size and 1 variant
    • Takes up and compensates for tolerances
    • High friction coefficients reduce ballast
    Dome FixPro in use with D-Dome 6

    Dome FixPro

    • Extends the application possibilities of Dome 6 systems
    • Fixed connection for roofs with inclination ≤ 5°
    • Required for roof pitches ≥ 3°
    • Recommended for roofs with low load reserves

    Dome Speed Spacer

    A new assembly aid

     

    • Simple alignment of the rails on the roof using the flexible spacer template
    • Simply adjust the module length and set the rail spacing
    • Suitable for all K2 flat roof systems

     

    References

    Components

    Downloads

    Product data sheet and brochures

    Assembly instructions and checklists

    Certificates

    Document type
    Certificate  Structural Analyses D-Dome 6.10
    Certificate  Structural Analyses S-Dome 6.10

    Videos

    Approved modules

    Here you find a list of modules which are approved for our Dome 6 flat roof systems.

     

    Technical data

     
    D-Dome 6.10
    S-Dome 6.10
    Scope of application

    Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

    Fastening type/­roof fixture

    • Ballasted and no roof penetration for inclination: ≤ 3°
    • With fixed connection at inclination with Dome FixPro Set: > 3°
    Require­ments

    • Permissible module dimensions (L×W×H): 1448-2390 × 950-1170 × 30-50mm
    • Minimum system size D-Dome / S-Dome: 2 supports (4 modules) / 2 modules
    • Clamping at the short module side permitted (see module approvals…)
    Technical specifications

    • Thermal separation after a maximum of 16m
    • Minimum distance to the edge of the roof 600mm

    • Thermal separation after a maximum of 15m
    • Minimum distance to the edge of the roof 600mm
    Inclination angle

    10°

    Material

    • Peak, SD, mounting rail, MidPlate, EndPlate, Connector, Porter, MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
    • Windbreaker: Magnelis
    • Mat S protective mat: EPDM
    • Small parts: stainless steel (1.4301) A2-70
    D-Dome 6.10
    Scope of application

    Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

    Fastening type/­roof fixture
    • Ballasted and no roof penetration for inclination: ≤ 3°
    • With fixed connection at inclination with Dome FixPro Set: > 3°
    Require­ments
    • Permissible module dimensions (L×W×H): 1448-2390 × 950-1170 × 30-50mm
    • Minimum system size D-Dome / S-Dome: 2 supports (4 modules) / 2 modules
    • Clamping at the short module side permitted (see module approvals…)
    Technical specifications
    • Thermal separation after a maximum of 16m
    • Minimum distance to the edge of the roof 600mm
    Inclination angle

    10°

    Material
    • Peak, SD, mounting rail, MidPlate, EndPlate, Connector, Porter, MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
    • Windbreaker: Magnelis
    • Mat S protective mat: EPDM
    • Small parts: stainless steel (1.4301) A2-70
    S-Dome 6.10
    Scope of application

    Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

    Fastening type/­roof fixture

    • Ballasted and no roof penetration for inclination: ≤ 3°
    • With fixed connection at inclination with Dome FixPro Set: > 3°
    Require­ments

    • Permissible module dimensions (L×W×H): 1448-2390 × 950-1170 × 30-50mm
    • Minimum system size D-Dome / S-Dome: 2 supports (4 modules) / 2 modules
    • Clamping at the short module side permitted (see module approvals…)
    Technical specifications

    • Thermal separation after a maximum of 15m
    • Minimum distance to the edge of the roof 600mm
    Inclination angle

    10°

    Material

    • Peak, SD, mounting rail, MidPlate, EndPlate, Connector, Porter, MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
    • Windbreaker: Magnelis
    • Mat S protective mat: EPDM
    • Small parts: stainless steel (1.4301) A2-70

    Side views

    D-Dome 6 Seitenansicht
    D-Dome 6.10
    S-Dome 6 Seitenansicht
    S-Dome 6.10