Bereich auswählen

    Dome V Systems

    • Our know-how of the last few years, many optimisations and improvements have gone into these systems.
    • Clearly ballast- and component-optimized system due to better friction coefficient of the flexible support pad
    • Simultaneous assembly of modules and mounting system as well as reduced screw connections ensure faster installation
    • Lower logistics costs due to lower transport volume
    Symbols Features Dome V Mounting Systems

    Soon no longer available!

    As of September, our Dome V system is no longer available.

     

    Switch to the further development Dome 6 now: Better features, cheaper and less ballast required - with long rails and unassembled or with short rails and pre-assembled.

    Optimized Dome V Systems

    A totally modular solution:

    • 1 Peak for all
    • 3 systems
    • 5 common components
    Mat V

    Mat V

    • Flexible Mat V made of EPDM – only 1 size and 1 variant
    • Absorbs and compensates for tolerances
    • Friction coefficients reduce ballast

     

     

    Dome V elevation

    Dome V elevation

    • Innovative geometry and connections to accommodate tolerances
    • Single screw connection and fast screw-in assembly of the SD with fixation via module clamp
    • Low transport volume
    Rail

    Rail

    • Integrated ballast tray almost eliminates the need for additional components
    • Short rails help compensate for roof tolerance
    Universal module clamps: MiniClamp MC/EC

    Universal module clamps: MiniClamp MC/EC

    • Clamping range 30 - 50 mm
    • Compatible with the MiniRail System
    • Optional: Equipotential bonding with TerraGrif possible

    References

    Components

    Downloads

    Available in the respective languages  

    Product data sheet and Brochure

    Assembly instructions and Checklist

    Tender specifications and certificates

    Document type
    Recommendations lightning protection and equipotential bonding
    Tender speci­fi­ca­tion  D-Dome V 10°
    Tender speci­fi­ca­tion  S-Dome V 10°
    Tender speci­fi­ca­tion  S-Dome V 15°
    Expert's report wind loads  D-Dome V 10°
    Expert's report wind loads  S-Dome V 10°
    Expert's report wind loads  S-Dome V 15°
    Certificate Structural Analyses  D-Dome V 10°
    Certificate Structural Analyses  S-Dome V 15°

    Videos

    Approved modules

    Here you find a list of modules which are approved for our Dome V flat roof systems.

     

    Technical data

     
    D-Dome V 10°
    D-Dome V 10°
    Scope of application

    Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

    Fastening type/roof fixture

    Ballasted; no roof penetration for inclination ≤ 3°

      Requirements

      • Permissible module dimensions (L×W×H): 1386-2100 × 985-1053 × 30-50mm
      • Minimum system size: 2 supports (4 modules)
      • Module approved for corner clamping (see approved modules…)
      Technical specifications

      • Thermal separation after a maximum of 15.5m
      • Minimum distance to the edge of the roof 600mm
      Inclination angle

      10°

      Material

      • Mounting rails, Peak, Basic, SD, Windbreaker and MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
      • Mat V protective mat: EPDM
      • Small parts: stainless steel (1.4301) A2-70
      D-Dome V 10°
      D-Dome V 10°
      Scope of application

      Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

      Fastening type/roof fixture

      Ballasted; no roof penetration for inclination ≤ 3°

      Requirements
      • Permissible module dimensions (L×W×H): 1386-2100 × 985-1053 × 30-50mm
      • Minimum system size: 2 supports (4 modules)
      • Module approved for corner clamping (see approved modules…)
      Technical specifications
      • Thermal separation after a maximum of 15.5m
      • Minimum distance to the edge of the roof 600mm
      Inclination angle

      10°

      Material
      • Mounting rails, Peak, Basic, SD, Windbreaker and MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
      • Mat V protective mat: EPDM
      • Small parts: stainless steel (1.4301) A2-70

      Side views

      D-Dome V side view
      D-Dome V
       
      S-Dome V 10°
      S-Dome V 15°
      S-Dome V 10°
      S-Dome V 15°
      Scope of application

      Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

      Fastening type/roof fixture

      Ballasted; no roof penetration for inclination ≤ 3°

        Requirements

        • Permissible module dimensions (L×W×H): 1550-1760 / 1880-2100 × 950-1053 × 30-50mm
        • Minimum system size: 2 modules
        • Module approved for corner clamping (see approved modules…)
        Technical specifications

        • Thermal separation after a maximum of 15.5m
        • Minimum distance to the edge of the roof 600mm
        Inclination angle

        10°

        15°

        Material

        • Mounting rails, Peak, Basic, SD and MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
        • Windbreaker: Magnelis
        • Mat V protective mat: EPDM
        • Small parts: stainless steel (1.4301) A2-70
        S-Dome V 10°
        S-Dome V 10°
        Scope of application

        Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

        Fastening type/roof fixture

        Ballasted; no roof penetration for inclination ≤ 3°

        Requirements
        • Permissible module dimensions (L×W×H): 1550-1760 / 1880-2100 × 950-1053 × 30-50mm
        • Minimum system size: 2 modules
        • Module approved for corner clamping (see approved modules…)
        Technical specifications
        • Thermal separation after a maximum of 15.5m
        • Minimum distance to the edge of the roof 600mm
        Inclination angle

        10°

        Material
        • Mounting rails, Peak, Basic, SD and MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
        • Windbreaker: Magnelis
        • Mat V protective mat: EPDM
        • Small parts: stainless steel (1.4301) A2-70
        S-Dome V 15°
        S-Dome V 15°
        Scope of application

        Flat roofs ≤ 5° with single ply membrane or bituminous roof covering, also on concrete, gravelled or green roofs

        Fastening type/roof fixture

          Requirements

          • Permissible module dimensions (L×W×H): 1550-1760 / 1880-2100 × 950-1053 × 30-50mm
          • Minimum system size: 2 modules
          • Module approved for corner clamping (see approved modules…)
          Technical specifications

          • Thermal separation after a maximum of 15.5m
          • Minimum distance to the edge of the roof 600mm
          Inclination angle

          15°

          Material

          • Mounting rails, Peak, Basic, SD and MiniClamps: Aluminium EN AW-6063 T66 and AW-6082 T6
          • Windbreaker: Magnelis
          • Mat V protective mat: EPDM
          • Small parts: stainless steel (1.4301) A2-70

          Side views

          S-Dome V side view
          S-Dome V 10°
          S-Dome V side view
          S-Dome V 15°